Categories

MITSUBISHI CONTROLLERS 300 SERIES



MITSUBISHI CONTROLLERS 300 SERIES

The 300 series controller has an adjustment for the brightness of the CRT. It is on one of the boards of the CRT unit, it is labeled RV402. It is mounted horizontally and the outer cage must be removed to make the adjustment.

The Mitsubishi FX-10 and FX-20 wire EDM machines use an M320 controller. After turning the power on, you must press the READY button to bring the controller up. It is not uncommon for one of these machines after being without power for a couple of weeks to need its software reloaded. When this happens the screen will be blank.

If you place the SYSTEM LOAD/SYSTEM START switch (this is the toggle switch below the floppy drive) from the SYSTEM START position to the SYSTEM LOAD position and power back up, you should have a screen. Reloading the software will erase all programs, offsets, E-Packs, soft limits, timers, etc.

The procedure for loading the software is:

1. Place SYSTEM LOAD/SYSTEM START switch (at floppy drive) to SYSTEM LOAD.
2. Insert SYSTEM SOFTWARE disk 1 of 3 in the floppy drive.
3. Press INPUT.
4. When prompted "ARE YOU READY?", insert disk 2 of 3. Once all three 
    disks have been loaded...
5. Cycle power.
6. Move switch to SYSTEM START.
7. Insert the ENGLISH DISK (Make sure the software version is the same 
    as the other disks).
8. Cycle power. (Display will say "LOADING LANGUAGE")
9. Once a normal screen is displayed (position, offset, etc.) remove 
    the disk. Lower right corner will display "LOAD PITCH ERROR"
10. Insert PITCH ERROR/BACKLASH disk.
11. Press PROGRAM EDIT.
12. Press 5 (corresponds to soft key option [I/O])
13. At DEV ( ) enter 1 (for MFD (floppy disk) ) DEV should be 
      highlighted before entering the one.
14. Press INPUT.
15. Press the right arrow key until "I/O MODE" is highlighted.
17. At I/O MODE ( ), enter 1 for IN (Input).
18. Press INPUT.
19. Press the down arrow key until "PROGRAM NO." is highlighted.
20. At PROGRAM NO. L ( ), enter "ALL".
21. Press INPUT.
22. Press 1 (I/O START).

You will be prompted that data is being loaded and when it is complete.
Once the software has been loaded you have to load the E-PACKS. These are the 9000 series programs which perform various functions.

To load the E-Packs:

1. Insert the E-Pack disk. (Normally, an E-Pack disk will have three or four files on it but generally speaking you only need to load the first file on the disk).
2. Press the PROGRAM EDIT key.
3. Press soft key number 5.
4. Press 1 (INPUT MODE).
5. Press INPUT.
6. Cursor to DATA KIND.
7. Press 1 (NC PRO.)
8. Press INPUT.
9. Cursor to MFD FILE.
10. Type in the file name.
11. Press INPUT.
12. Press soft key number 1 (I/O START).

You will be prompted that data input is complete.

On the 320 controller, connector CNP3 on the chassis power supply is a three pin Molex connector which supplies 110 vac to the CRT. On the Mitsubishi FX-10 and FX-20 EDM machines the wires from this connector go to the CRT ON/OFF switch. On this power supply the incoming power (100vac) is supplied to terminals ACINH and ACINL.

The magazine capacity for the Max-3 Rebel with the 335 controller is stored at R1905 in the form of a decimal number.

If the tools get confused on the Max-3 with the 335, manually move the magazine to pot number one. Make R1901 = 1 and make R1905 = the magazine capacity.


600 SERIES

On a 635 controller, when prompted to enter a password to access the Machine Parameters, enter ..Share your problem. contact us..